This is a working overview of RP-HPLC, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2025-10-25 and is reviewed periodically as new material appears.
Orthogonal methods reduce the chance that a single technique misses an impurity. Capillary electrophoresis separates by charge-to-size ratio and can resolve variants that co-elute under one set of HPLC conditions. Amino acid analysis reports composition after hydrolysis and confirms the presence of expected residues. Karl Fischer titration measures water content, while ion chromatography can quantify counterions. No single number captures all aspects of sample quality, so reports often combine several measurements.
Peptide purity testing uses separation methods to estimate the proportion of a sample that corresponds to the target sequence. Reverse-phase high-performance liquid chromatography is the most common technique, separating peptides by hydrophobicity on a nonpolar column. Ultraviolet detection at 214 nm records peptide bonds and aromatic residues. The resulting chromatogram is reported as area percent, which reflects relative absorbance rather than absolute mass. This distinction matters because water, counterions, and residual solvents do not appear in the peptide peak.
Other methods address specific purity concerns. Amino acid analysis gives compositional data after hydrolysis, while capillary electrophoresis separates by charge-to-mass ratio. Karl Fischer titration measures residual water, and gas chromatography can detect residual solvents. Nuclear magnetic resonance can identify organic impurities but is less sensitive for trace levels. No single test covers all possible impurities, so purity testing usually combines orthogonal methods and reports the conditions used. The choice of methods is guided by the impurity classes of interest.
Reverse-phase high-performance liquid chromatography (RP-HPLC) is widely used to estimate peptide purity. It separates components by hydrophobicity on a column with a water-organic mobile phase. Ultraviolet absorbance at 214 nm or 220 nm detects peptide bonds. The main peak area as a percentage of total peak area gives a purity figure. This figure depends on column, gradient, wavelength, and how peaks are integrated, so it is method-specific rather than absolute.
| Property | Value | Notes |
|---|---|---|
| Primary purity method | Reverse-phase HPLC | Separates peptides by hydrophobicity; reports area percent. |
| Identity confirmation | Mass spectrometry | Electrospray or MALDI; matches observed mass to expected sequence. |
| Orthogonal separation | Capillary electrophoresis | Separates by charge-to-size ratio; complements HPLC. |
| Water content | Karl Fischer titration | Water dilutes peptide mass and affects concentration calculations. |
| Counterion | Trifluoroacetate or acetate | Common counterions alter net peptide content in lyophilized powder. |
Sampling and sample preparation influence measured purity. Peptides are often hygroscopic, so weighing should occur quickly under controlled humidity to avoid water uptake. Complete dissolution in a suitable solvent is necessary before injection; undissolved material can block columns or distort results. Filtration removes particulates but may also remove aggregates if the filter pore size is too small. Impurities can originate from synthesis, cleavage, purification, or storage, and forced degradation under heat, light, oxidation, or pH extremes can help identify degradation pathways.
Regulatory and accreditation expectations depend on the peptide's intended use. Research reagents may be tested with in-house methods, while pharmaceutical development follows validated procedures and pharmacopeial chapters where applicable. Method validation commonly examines accuracy, precision, specificity, linearity, range, and limits of detection and quantitation. Laboratories accredited to ISO/IEC 17025 must document competence, equipment calibration, and uncertainty. Comparing purity results across laboratories remains difficult because different columns, gradients, detection wavelengths, and integration rules can change reported values; open questions include how best to standardize impurity identification and reporting for diverse peptide products.
Quality control for peptides places purity testing within a documented system that includes specifications, test methods, and acceptance criteria. A certificate of analysis typically reports appearance, chromatographic purity, mass confirmation, and storage conditions. System suitability checks, blank injections, and reference standards help ensure that an analytical run is valid. Traceability requires records of sample preparation, instrument settings, and data processing. No single purity threshold applies to all peptides or uses, so specifications are set according to the intended application and risk assessment.
Peptide purity can change during storage, handling, and reconstitution, and lyophilized peptides are generally more stable than solutions because water promotes hydrolysis and aggregation. Residual moisture, oxygen, and trace metals can accelerate degradation even in solid form. Temperature fluctuations during shipping may cause condensation and local moisture uptake. Quality control therefore includes appearance, water content, and analytical testing before and after storage challenges. Peptides containing cysteine, methionine, or tryptophan are especially susceptible to oxidation, while asparagine and glutamine residues can deamidate under neutral or alkaline conditions.
Analytical quality control compares a stored sample against a baseline profile. Reverse-phase chromatography remains common, but stability studies may also use mass spectrometry to detect oxidation, deamidation, or truncation products. Accelerated aging at elevated temperature can reveal degradation pathways, although extrapolation to room temperature is uncertain. Forced degradation studies expose peptides to heat, light, acid, base, and oxidants to identify likely breakdown products. Documentation should record lot number, storage history, and the exact method used for each measurement.
Quality control specifications for peptides typically include appearance, identity, purity by RP-HPLC, water content, counterion content, and residual trifluoroacetic acid. Karl Fischer titration measures water, while ion chromatography or elemental analysis can quantify counterions. Purity specifications may be set at 95% or 98% area percent, but the appropriate threshold depends on the application. For research reagents, a lower purity may be acceptable if identity is confirmed. For assays sensitive to impurities, higher purity and orthogonal testing are often required.
Handling and storage influence measured purity, and peptides can oxidize, deamidate, aggregate, or adsorb to surfaces over time. Lyophilized powders stored at -20 °C or lower are generally more stable than solutions, though some sequences require different conditions. Repeated freeze-thaw cycles can promote aggregation and loss, so testing after storage checks whether purity has changed. Stability-indicating methods compare stressed and unstressed samples to detect degradation pathways. Light exposure and pH can also accelerate modification.
Solid-phase peptide synthesis can produce truncated sequences when coupling reactions fail. Deletion peptides lack one or more internal residues, while truncation peptides end prematurely. Side reactions include aspartimide formation, oxidation of methionine, and aggregation during chain assembly. Crude synthetic peptides therefore contain target peptide plus related impurities, counterions, residual solvents, and water. Purification by preparative chromatography reduces these impurities but does not remove every closely related species, including some that differ by a single amino acid.
Impurity profiling identifies and quantifies substances that coexist with the target peptide. These include deletion sequences, truncated peptides, oxidized variants, and residual protecting groups from synthesis. Reversed-phase chromatography can separate many of these impurities, but co-elution remains a challenge for closely related species. Mass spectrometry helps assign identities to impurity peaks, and impurity limits are often set as area percentages relative to the main peak. Regulatory guidelines for research-grade peptides are less strict than those for therapeutic products, so specifications vary by supplier.
Quality control for peptides involves setting specifications for identity, purity, and counterion content. Batches are tested against these specifications before release. Purity specifications often require a minimum area percentage by high-performance liquid chromatography, such as 95% or 98%, depending on the intended application. Additional tests may include water content, acetate or trifluoroacetate content, and residual solvents. These parameters affect the net peptide content and the accuracy of subsequent laboratory experiments.
Stability testing examines how peptide purity changes over time under defined conditions. Accelerated studies use elevated temperatures and humidity to predict degradation pathways, while long-term studies store samples at recommended temperatures. Common degradation reactions include oxidation of methionine, deamidation of asparagine, and hydrolysis of peptide bonds. The results inform expiration dates and storage recommendations for research materials. Lyophilized peptides are generally more stable than solutions, but both forms can degrade if exposed to moisture, oxygen, or repeated freeze-thaw cycles.
White was married to his wife Edna for more than 40 years. He died unexpectedly on February 14, 1980, in Santa Barbara, California, where he had gone that day from his home in Palo Alto to deliver a lecture at the University of California. Several awards in the field of biochemistry have been named for White, including at Oakland University in Michigan, Wayne State University, George Washington University School of Medicine and the Gladstone Institutes. 1935 – Traveling Fellowship, American Physiological Society, for the XVth International Congress of Physiology (Leningrad and Moscow) 1938 – Eli Lilly Prize in Biochemistry 1960 – Distinguished Alumni Award, University of Denver 1967 – Sesquicentennial Alumni Award, University of Michigan 1969 – Borden Award, Association of American Medical Colleges 1959 – Doctor of Humane Letters, Yeshiva University 1975 – Doctor of Science, University of Denver
Alexandra C. Newton is a Canadian and American biochemist. She is a Distinguished Professor of pharmacology at the University of California, San Diego. Newton runs a multidisciplinary Protein kinase C and Cell signaling biochemistry and cell biology research group in the School of Medicine, investigating molecular mechanisms of signal transduction in the Phospholipase C (PLC) and Phosphoinositide 3-kinase (PI3 kinase, or PI3-K) signaling pathways. She has been continuously funded by the US National Institutes of Health since 1988. Newton was born in Cape Town, South Africa, and was schooled in Vancouver, Athens, and Aix-en-Provence. She graduated in 1980 from the Simon Fraser University in Canada, where she was awarded a 1st-class honours degree in biochemistry and French literature. She received her PhD in chemistry in 1986 from Stanford University, working with Wray H. Huestis on a thesis examining band 3, a red cell membrane protein.
The Association of Public Health Laboratories (APHL) is a membership organization in the United States representing the laboratories that protect the health and safety of the public. APHL serves as a liaison between public health laboratories and federal and international agencies. Membership consists of local, state, county, and territorial public health laboratories; public health environmental, agricultural and veterinary laboratories; and corporations and individuals with an interest in public health and laboratory science. APHL is a non-profit, 501(c)(3) organization with a history of over fifty years.
Prior to development of AS9100 standards for Quality Management Systems, the U.S. military applied two specifications to supplier quality and inspection programs, respectively, MIL-Q-9858A Quality Program Requirements, and MIL-I-45208A Military Specification: Inspection System Requirements. For years these specifications had represented the basic tenets of the aerospace industry. However, when the U.S. government adopted ISO 9001, it withdrew those two quality standards. Large aerospace companies then began requiring their suppliers to develop quality programs based on ISO 9001. As technologies evolve, and industries become more specialized, it is likely that more updates will be made to these standards and additional specialty Quality Management Systems (QMS) requirements for various industries.
ACTA2 (actin alpha 2) is an actin protein with several aliases including alpha-actin, alpha-actin-2, aortic smooth muscle or alpha smooth muscle actin (α-SMA, SMactin, alpha-SM-actin, ASMA). Actins are a family of globular multi-functional proteins that form microfilaments. ACTA2 is one of six different actin isoforms and is involved in the contractile apparatus of smooth muscle. ACTA2 (as with all the actins) is extremely highly conserved and found in nearly all mammals. In humans, ACTA2 is encoded by the ACTA2 gene located on 10q22-q24. Mutations in this gene cause a variety of vascular diseases, such as thoracic aortic disease, coronary artery disease, stroke, Moyamoya disease, and multisystemic smooth muscle dysfunction syndrome. ACTA2 (commonly referred to as alpha-smooth muscle actin or α-SMA) is often used as a marker of myofibroblast formation. Studies have shown that ACTA2 is associated with TGF-β pathway that enhances contractile properties of hepatic stellate cells leading to liver fibrosis and cirrhosis.
Sources: en.wikipedia.org
ATC code H01 Pituitary and hypothalamic hormones and analogues is a therapeutic subgroup of the Anatomical Therapeutic Chemical Classification System, a system of alphanumeric codes developed by the World Health Organization (WHO) for the classification of drugs and other medical products. Subgroup H01 is part of the anatomical group H Systemic hormonal preparations, excluding sex hormones and insulins. Codes for veterinary use (ATCvet codes) can be created by placing the letter Q in front of the human ATC code: for example, QH01. ATCvet codes without corresponding human ATC codes are cited with the leading Q in the following list.National versions of the ATC classification may include additional codes not present in this list, which follows the WHO version. H01AA01 Corticotropin H01AA02 Tetracosactide H01AB01 Thyrotropin alfa H01AC01 Somatropin H01AC02 Somatrem H01AC03 Mecasermin H01AC04 Sermorelin H01AC05 Mecasermin rinfabate H01AC06 Tesamorelin H01AC07 Somapacitan H01AC08 Somatrogon H01AC09 Lonapegsomatropin H01AX01 Pegvisomant QH01AX90 Capromorelin
As with other hormones, hGH levels often decline with age, but this decrease is not necessarily bad. At least one epidemiological study suggests that people who have high levels of hGH are more apt to die at younger ages than those with lower levels of the hormone. Researchers have also studied animals with genetic disorders that suppress growth hormone production and secretion and found reduced growth hormone secretion may actually promote longevity in those species that have been tested. The Clinical Interventions in Aging review also stated that although the decreasing levels of the hormone seen in the elderly might reduce quality of life, this change could protect from age-related diseases and cited evidence linking GH to cancer. This concern was mirrored in a 2008 review published in Clinical Endocrinology, which stated that the risk of increasing the incidence of cancer was a strong argument against the use of this hormone as an "elixir of youth" in healthy adults.
One mechanism through which BDNF appears to maintain elevated levels of neuronal excitation is through preventing GABAergic signaling activities. While glutamate is the brain's major excitatory neurotransmitter and phosphorylation normally activates receptors, GABA is the brain's primary inhibitory neurotransmitter and phosphorylation of GABAA receptors tend to reduce their activity. Blockading BDNF signaling with a tyrosine kinase inhibitor or a PKC inhibitor in wild type mice produced significant reductions in spontaneous action potential frequencies that were mediated by an increase in the amplitude of GABAergic inhibitory postsynaptic currents (IPSC). Similar effects could be obtained in BDNF knockout mice, but these effects were reversed by local application of BDNF. This suggests BDNF increases excitatory synaptic signaling partly through the post-synaptic suppression of GABAergic signaling by activating PKC through its association with TrkB. Once activated, PKC can reduce the amplitude of IPSCs through to GABAA receptor phosphorylation and inhibition. In support of this putative mechanism, activation of PKCε leads to phosphorylation of N-ethylmaleimide-sensitive factor (NSF) at serine 460 and threonine 461, increasing its ATPase activity which downregulates GABAA receptor surface expression and subsequently attenuates inhibitory currents.
While the Arrhenius concept is useful for describing many reactions, it is also quite limited in its scope. In 1923, chemists Johannes Nicolaus Brønsted and Thomas Martin Lowry independently recognized that acid–base reactions involve the transfer of a proton. A Brønsted–Lowry acid (or simply Brønsted acid) is a species that donates a proton to a Brønsted–Lowry base. Brønsted–Lowry acid–base theory has several advantages over Arrhenius theory. Consider the following reactions of acetic acid (CH3COOH), the organic acid that gives vinegar its characteristic taste:
Sources: en.wikipedia.org
The ABC domain consists of two domains, the catalytic core domain similar to RecA-like motor ATPases and a smaller, structurally diverse α-helical subdomain that is unique to ABC transporters. The larger domain typically consists of two β-sheets and six α helices, where the catalytic Walker A motif (GXXGXGKS/T where X is any amino acid) or P-loop and Walker B motif (ΦΦΦΦD, of which Φ is a hydrophobic residue) is situated. The helical domain consists of three or four helices and the ABC signature motif, also known as LSGGQ motif, linker peptide or C motif. The ABC domain also has a glutamine residue residing in a flexible loop called Q loop, lid or γ-phosphate switch, that connects the TMD and ABC. The Q loop is presumed to be involved in the interaction of the NBD and TMD, particularly in the coupling of nucleotide hydrolysis to the conformational changes of the TMD during substrate translocation. The H motif or switch region contains a highly conserved histidine residue that is also important in the interaction of the ABC domain with ATP. The name ATP-binding cassette is derived from the diagnostic arrangement of the folds or motifs of this class of proteins upon formation of the ATP sandwich and ATP hydrolysis.
ADP-ribose is an intermediate that is produced during the metabolism of NAD+, mono- or poly-unsaturated proteins, and cyclic-ADP ribose. ADP-ribose is a protein-glycating agent, and excess levels of ADP-ribose in the cell can cause non-enzymatic ADP-ribosylation. Non-enzymatic ADP-ribosylation can inactivate protein targets that contain nucleotide-binding sites when the adenylate moiety of ADP-ribose binds to them, and it can also interfere with metabolic regulation that occurs via enzymatic ADP-ribosylation. For example, actin polymerization is inhibited by non-enzymatic ADP-ribosylation at a Cys residue. Thus, it is believed that ADPRase functions in general as a house-cleaning enzyme to eliminate potentially deleterious ADP-ribose from the cell. In the literature, the detoxifying role of ADPRase is directly supported in E. coli cells. But in mammalian cells, there is only an indirect evidence linking ADPRase to a detoxifying role, and this comes from studies of the very specific rat liver ADPRibase-I by cytotoxic agents.
An alcohol burner or spirit lamp is a piece of laboratory equipment used to produce an open flame. It can be made from brass, glass, stainless steel or aluminium. Alcohol burners are preferred for some uses over Bunsen burners for safety purposes, and in laboratories where natural gas is not available. Their flame is limited to approximately 5 centimeters (two inches) in height, with a comparatively lower temperature than the gas flame of the Bunsen burner. While they do not produce flames as hot as other types of burners, they are sufficiently hot for performing some chemistries, standard microbiology laboratory procedures, and can be used for flame sterilization of other laboratory equipment. A small alcohol burner is also preferred for camping when the need for fire is modest. It burns the alcohol vapor that rises due to the heat from the flame through the holes on the top perimeter of the container. Typical fuel is denatured alcohol, methanol, or isopropanol. A cap is used as a snuffer for extinguishing the flame.
Sources: en.wikipedia.org
It measures the relative ultraviolet absorbance area of peptide peaks, usually at 214 nm. It does not directly measure mass, water, counterions, or co-eluting species.
HPLC and mass spectrometry answer different questions: HPLC estimates separation purity, while mass spectrometry confirms molecular mass. Orthogonal methods reduce the risk that one technique misses an impurity.
Yes. Area percent excludes water, counterions, residual solvents, and any species that co-elute with the target peak. Net peptide content can therefore be lower than the reported HPLC purity.
It usually refers to the relative area of the main peak in a chromatographic separation, such as RP-HPLC. It estimates the proportion of UV-absorbing material in that peak, not the absolute mass fraction of the target peptide. Different methods can give different percentages.